● Includes stainless fasteners and dual o-rings for water/dust sealing
● Direct drop-in fit for S1/S2 pod openings
● Ideal for offroad enthusiasts adding front-facing or rock-crawl visibility
● Camera not included (compatible with Wolfbox G900 type camera bodies)
● Hardware: All stainless screws + o-rings included
● Professionally printed in weather-resistant ASA filament
● Designed and made in the USA by Americans

The post Baja Designs S1 & S2 Flush Mount Adapter for Wolfbox G900 Type Cameras appeared first on Crossroads 3D.

10-degree down angle is a screw mount designed for the Ford Transit High Roof, and has a wire exit underneath the bottom that goes straight down (intended to mount over top of a drilled hole.)

• Mount your Wolfbox camera to any flat surface
• Choose mount type: Screws or automotive molding tape (clean surface before use)
• Mount is precision fit: includes integrated wire channel to run the cord out the back
• Fits the Wolfbox G840, G850 rear camera only.
• Screws and/or tape included
• Designed and Made in the USA by Americans
• Professionally printed in ASA

The post Protective Cover Mount for Wolfbox Camera G840, G850 (Screw or Adhesive mount) appeared first on Crossroads 3D.

Mount your Wolfbox rear camera high up on flat surfaces like camper roofs, trailer tops, or high-roof van exteriors with this angled adhesive pod. The built-in 12-degree downward tilt provides optimal rear viewing without awkward adjustments—perfect for elevated installations where a level mount would point too high.

• Designed for Wolfbox G900, G900 Pro, G900 Tripro, and similar rear camera models (check photos for match)
• 12° built-in down angle ideal for high placements on campers, travel trailers, fifth wheels, or roof-mounted setups
• Sleek protective cover shields the camera from rain, dust, UV, and road debris for reliable all-weather performance
• Choose from stainless screw or automotive-grade adhesive mounting for secure mounting on metal, fiberglass, or composite surfaces
• Wire exit options: choose bottom cable exit or rear exit when ordering
• Durable, weather-resistant construction holds up in outdoor vehicle environments
• Easy install: snap in camera, install base plate, and install. (Camera NOT included – mount and cover only)
• Proudly designed and made in the USA by Americans
• Made from ASA

Great for high-roof cargo vans like Ford Transit (including high-roof models), Mercedes-Benz Sprinter (high-roof), Ram ProMaster (high-roof), and similar setups where you need downward-angled rear visibility from elevated positions.

Not sure if it fits your setup? Message me with your vehicle details or a photo—I'll confirm compatibility fast!

The post Wolfbox G900 High Mount Camera Mount Pod,12-degree Down Angle, Adhesive or Screw Mount, USA Made appeared first on Crossroads 3D.

• All 4 clamps included for rear or top-mount

The post 12-Gang Overhead-Mounted Switch Panel appeared first on Crossroads 3D.

The camera snaps into the protective cover securely. Top hole is for camera removal.

• Mount your rearview backup camera to any flat surface
• Choose between adhesive mount or screw mount
• Mount is secure and precision fit: includes integrated wire channel to run the cord out the back
• Fits the displayed camera type only
• All fasteners included
• Top hole is for camera removal
• Designed and Made in the USA by Americans
• Professionally printed in ASA

The post Protective Cover Mount for Rearview Camera (Screw or Adhesive mount) appeared first on Crossroads 3D.

10-degree down angle is a screw mount designed for the Ford Transit High Roof, and has a wire exit underneath the bottom that goes straight down (intended to mount over top of a drilled hole.)

• Mount your G900 camera to any flat surface
• Choose mount type: Screws or automotive molding tape (clean surface before use)
• Choose finish type: none (black) or pro auto paint.
• Mount is precision fit: includes integrated wire channel to run the cord out the back
• Fits the Wolfbox G900 Tripro rear camera only.
• Screws and/or tape included
• Designed and Made in the USA by Americans
• Professionally printed in ASA

The post Protective Cover Mount for Wolfbox Camera G900, G930 (Screw or Adhesive mount) appeared first on Crossroads 3D.

• Convenient location
  Place your switches overhead on the bar.
  Top-mounted units are "ambidextrous" - you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
  Rear-mount option available for when vertical space is a premium
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Features
• Large side hatch to fit pre-wired kits with large quick-connect plugs

The post Bar Mount for 5-Gang Pre-Wired Switch Panel appeared first on Crossroads 3D.

• Mounts the MapDCCD G2 to any round bar
• Choose your bar clamp size when ordering
• Includes all installation hardware
• Professionally 3D Printed in ABS
• Designed and made in the USA

The post MapD CCD G2 Roll Bar Mount appeared first on Crossroads 3D.

• Convenient location
  Place your radio overhead on the roll bar. Rotate the clamp to position the radio forward or rearward.
• Designed to fit
  Bar clamps are precision for your bar, no shims necessary. Angled back for use with SXS windshields
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses Phillips screwdrivers
• Attractive and Durable
  This product is professionally 3D printed in ABS.
• Customizable
  If you need a mount for another bar size, or other combination of switches and circle-holes, or any other powered panel type or brand, contact me.

Example radios that this will fit:

• BOSS Audio Systems MGR350B
• BOSS Audio Systems MGR450B
• BOSS Audio Systems MGR300B
• Kicker 46KMC2 Weather-Resistant Gauge-Style Media Center with Bluetooth
• Generic Marine Gauge Stereo Receiver

The post Roll-Bar Mount for 3″ Marine Radios appeared first on Crossroads 3D.

The post Roll-bar Mount for Emergency Switch (ESTOP button) appeared first on Crossroads 3D.

The post 8-Gang Switch Panel + Emergency-stop mount for Roll Bar appeared first on Crossroads 3D.

3/4" wire exit hole on the right (passenger) side with larger cover for quick disconnect plugs.

• Convenient location
  Place your switches overhead on the bar. This unit is rear mounted for situations where there is limited vertical space.
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Box dimensions:
  5" wide, 3.5" deep, 2 7/8" high.

The post Bar Mount for 4-Gang Pre-Wired Switch Panel [Rear Mount] appeared first on Crossroads 3D.

Works with or without the Switch-Pros face bezel.

• Convenient location
  Mount your RCR-12 overhead on the bar. You can mount your panel over or under the bar, forward, or rearward (toward or away from your face.)
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Attractive and Durable
  This product is professionally 3D printed.
• Customizable
  If you need a switch panel for another bar size, contact me.

The post Bar Mount for Switch-Pros RCR-12 Powered Switch Panel appeared first on Crossroads 3D.

• Convenient location
  Place your switches overhead on the bar. This unit is "ambidextrous:" you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.

The post Bar Mount for Switch-Pro 9100 and Additional Custom Slot appeared first on Crossroads 3D.

• Convenient location
  Place your switches overhead on the bar. This unit is "ambidextrous:" you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Attractive and Durable
  This switch panel won't warp in the heat - the material used has similar characteristics as the factory plastic in your machine. This product is professionally 3D printed in ABS.
• Customizable
  If you need a switch panel for another bar size, or other combination of switches and circle-holes, or any other powered panel type or brand, contact me.

The sPOD SourceLT Universal Switch Panel panel can be purchased here.

The post Roll-Bar Mount for sPOD SourceLT 6-Gang Switch Panel appeared first on Crossroads 3D.

• Convenient location
  Place your switches overhead on the bar. This unit is "ambidextrous:" you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
  Rear-mount option available for when vertical space is a premium
• Choose "Adhesive Mount" when you need a simple attachment to a flat surface (no bar clamp)
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Features
  Optional holes for in-cab down-lighting - choose to have two holes for 10mm-diameter down-lights
  Large side hatch to fit pre-wired kits with large plugs

The post Bar Mount for 8-Gang Pre-Wired Switch Panel appeared first on Crossroads 3D.

• Convenient location
  Place your switches overhead on the bar. This unit is "ambidextrous:" you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
  Rear-mount option available for when vertical space is a premium
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Features
  Optional holes for in-cab down-lighting - choose to have two holes for 10mm-diameter down-lights
• Large side hatch to fit pre-wired kits with large quick-connect plugs

The post Bar Mount for 6-Gang Pre-Wired Switch Panel appeared first on Crossroads 3D.

The post Grab Handle Tie Downs appeared first on Crossroads 3D.

• This vent is designed with a 2" (51mm) OD hose barb for connection with common flex vent hoses.
• Internal directional louvres offer a wide distribution of air
• Minimum Temperature:  -4° F (-20° C)
• Maximum Temperature:  200° F (95° C)
• Made from ABS

The post Universal Cab Heater Defroster Vent appeared first on Crossroads 3D.

• Convenient location
  Mount your Auxbeam overhead on the bar. This unit is "ambidextrous:" you can mount your switch panel over or under the bar, forward, or rearward (toward or away from your face.)
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.

Be sure to choose the correct 6-Gang option (for AR-600 or BC60 model Auxbeam panel)
Be sure to choose the correct 8-Gang option(GB80, BB80 GA80, BB80, AR-800 or XL)

Auxbeam Model Fitment:

• AR-800
• BA80
• BB80
• GB80
• GA80
• BC60
• GC60
• RA80 XL
• RB80 XL

The post Bar Mount for Auxbeam 8 or 6-Gang Switch Panel appeared first on Crossroads 3D.