This roll-bar-mounted switch panel holds 12 standard sized rocker switches. The whole mount is 12 3/4″ wide.

• All 4 clamps included for rear or top-mount

Check out the other sizes:

• 2-Gang roll-bar mounted panel
• 3-Gang roll-bar mounted panel
• 4-Gang roll-bar mounted panel
• 6-Gang roll-bar mounted panel
• 8-Gang roll-bar mounted panel
• 8-Gang flat-mounted panel

This roll-bar-mounted switch panel pairs up with 5-Gang pre-wired switch panels, like the “FXC” or “Nilight” brand panels and others.

• Convenient location
  Place your switches overhead on the bar.
  Top-mounted units are “ambidextrous” – you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
  Rear-mount option available for when vertical space is a premium
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Features
• Large side hatch to fit pre-wired kits with large quick-connect plugs

This panel is designed to mount the Auxbeam “slim” AS-R60 Powered Switch Controller, mounted to the Honda Pioneer 700 (2016-2022)

• Convenient location
  This switch panel replaces the center warning plate in your Pioneer 700.
• Easy install
  Drill out the rivets holding the warning plate, then use a utility knife to cut the hole. Fastens with 6 push-clips (included).
• Handy Storage
  An an option, get the storage slot to hold your phone, gloves, or keys. Storage pocket is 1″ wide, 3.5″ tall, and 3″ deep.
• Circle Slots
  Two round knockouts allow you to easily open up holes for voltmeters, USB plugs, and more.

(Auxbeam AS-R60 powered switch panel not included)

This roll-bar-mounted switch panel pairs up with 4-Gang pre-wired switch panel, like the “FXC” brand and others. (available here).

3/4″ wire exit hole on the right (passenger) side with larger cover for quick disconnect plugs.

• Convenient location
  Place your switches overhead on the bar. This unit is rear mounted for situations where there is limited vertical space.
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Box dimensions:
  5″ wide, 3.5″ deep, 2 7/8″ high.

This bar mount for the Switch-Pros RCR-12 12-button powered switch panel. It gives you a secure mount on any round bar.

Works with or without the Switch-Pros face bezel. 

• Convenient location
  Mount your RCR-12 overhead on the bar. You can mount your panel over or under the bar, forward, or rearward (toward or away from your face.)
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Attractive and Durable
  This product is professionally 3D printed.
• Customizable
  If you need a switch panel for another bar size, contact me.

Check out the other sizes:

• 2-Gang roll-bar mounted panel
• 3-Gang roll-bar mounted panel
• 4-Gang roll-bar mounted panel
• 6-Gang roll-bar mounted panel
• 8-Gang roll-bar mounted panel

Assembly Instruction:

• This electronics switch panel for the 2023+ Honda Pioneer 700 holds standard rocker switches. (Not included.)
  • Convenient location
    This switch panel replaces the center cubby in your Pioneer 700 (2023 and newer).
  • Easy install
    Precision snap-in fitment to existing holes in dash (remove mesh pocket cover first).
  • Keeps Storage
    Panel shelf coveres the lower portion where the switches are installed, keeping the upper portion of the storage cubby uncovered to act as a pocket for phone, keys, etc.

  Panel is professionally 3D printed for a factory appearance.

This roll-bar-mounted switch panel pairs up with a Switch-Pro SP 9100 8-Gang pre-wired switch panel plus another hole or slot of your choice to the side. (Contact me for your customization needs.)

• Convenient location
  Place your switches overhead on the bar. This unit is “ambidextrous:” you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.

This electronics switch panel for the 2023+ Honda Pioneer 700 mounts the Auxbeam XL powered switch panel to your dash. (not included.)

• Convenient location
  This switch panel replaces the center cubby in your Pioneer 700 (2023 and newer).
• Easy install
  Precision snap-in fitment to existing holes in dash (remove mesh pocket first). Drill 2 holes for push clips.

XL Panel can be purchased here: Auxbeam XL Switch Panel

Panel mount is professionally 3D printed for a factory appearance.

This electronics switch panel for the 2023+ Honda Pioneer 700 holds Auxbeam 8 or 6-gang powered switch panels and includes a circular knockout for USB/voltage meter mounting. (Auxbeam panels and other electronics not included.)

• Convenient location
  This switch panel replaces the center cubby in your Pioneer 700 (2023 and newer).
• Easy install
  Precision snap-in fitment to existing holes in dash (remove mesh pocket first).
• Keeps Storage
  Keeps the top portion of the P700 storage cubby to act as a pocket for phone, keys, etc.

Panel is professionally 3D printed for a factory appearance.

• Auxbeam 8-gang switch panel
• Auxbeam 6-gang switch panel

Auxbeam Model Fitment:

• • BA80
  • BB80
  • GB80
  • GA80
  • BC60
  • GC60

• Convenient location
  Place your switches overhead on the bar. This unit is “ambidextrous:” you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Attractive and Durable
  This switch panel won’t warp in the heat – the material used has similar characteristics as the factory plastic in your machine. This product is professionally 3D printed in ABS.
• Customizable
  If you need a switch panel for another bar size, or other combination of switches and circle-holes, or any other powered panel type or brand, contact me.

The sPOD SourceLT Universal Switch Panel panel can be purchased here.

• 2-Gang roll-bar mounted panel
• 3-Gang roll-bar mounted panel
• 4-Gang roll-bar mounted panel
• 6-Gang roll-bar mounted panel
• 8-Gang roll-bar mounted panel

• Convenient location
  Place your switches overhead on the bar. This unit is “ambidextrous:” you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
  Rear-mount option available for when vertical space is a premium
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Features
  Optional holes for in-cab down-lighting – choose to have two holes for 10mm-diameter down-lights
  Large side hatch to fit pre-wired kits with large plugs

This roll-bar-mounted switch panel pairs up with 6-Gang pre-wired switch panels, like the “FXC” or “Nilight” brand panels and others. (available here)

• Convenient location
  Place your switches overhead on the bar. This unit is “ambidextrous:” you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
  Rear-mount option available for when vertical space is a premium
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Features
  Optional holes for in-cab down-lighting – choose to have two holes for 10mm-diameter down-lights
• Large side hatch to fit pre-wired kits with large quick-connect plugs

​

• This bar mount for the popular Auxbeam 8-Gang or 6-Gang powered switch panels gives you a secure, flush-fit mount on any Round bar. Jeep, Honda Pioneer, Polaris RZR, Kawasaki Teryx, Yamaha Wolverine, RMAX, YXZ1000 and others.

  • Convenient location
    Mount your Auxbeam overhead on the bar. This unit is “ambidextrous:” you can mount your switch panel over or under the bar, forward, or rearward (toward or away from your face.)
  • No cutting or drilling
    No chopping up of your dash!
  • Easy install
    Installation is simple and uses a Phillips screwdriver.

  Be sure to choose the correct 6-Gang option (for AR-600 or BC60 model Auxbeam panel)
  Be sure to choose the correct 8-Gang option(GB80, BB80 GA80, BB80 or XL)

  Auxbeam Model Fitment:

  • BA80
  • BB80
  • GB80
  • GA80
  • BC60
  • GC60
  • RA80 XL
  • RB80 XL

  

  

Check out my other rocker-switch panels:

• 2-Gang roll-bar mounted panel
• 3-Gang roll-bar mounted panel
• 4-Gang roll-bar mounted panel
• 6-Gang roll-bar mounted panel
• 8-Gang roll-bar mounted panel

Assembly Instruction:

This bar mount for the Switch-Pro SP9100 gives you a secure, flush-fit mount on any round bar. 

• Convenient location
  Mount your SP 9100 overhead on the bar. This unit is “ambidextrous:” you can mount your panel over or under the bar, forward, or rearward (toward or away from your face.)
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Attractive and Durable
  The walls are 1/8″ thick. This switch panel won’t warp in the heat – the material used has similar characteristics as the factory plastic in your machine. This product is 3D printed.
• Customizable
  If you need a switch panel for another bar size, or other combination of switches and circle-holes, contact me.

Check out the other sizes:

• 2-Gang roll-bar mounted panel
• 3-Gang roll-bar mounted panel
• 4-Gang roll-bar mounted panel
• 6-Gang roll-bar mounted panel
• 8-Gang roll-bar mounted panel

Assembly Instruction:

This roll-bar-mounted switch panel holds 2 standard sized rocker switches.

• Convenient location
  Place your switches overhead on the bar. This unit is “ambidextrous:” you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Attractive and Durable
  This 2-gang switch box is 2 3/4″ (2.75″ inch) wide. The walls are 1/8″ thick. This switch panel won’t warp in the heat – the material used has similar characteristics as the factory plastic in your machine. This product is 3D printed.
• Customizable
  If you need a switch panel for another bar size, or other combination of switches and circle-holes, contact me.

I don’t sell electronics, but you can get switches and things on Amazon: SXS Rocker Switches

Check out the other sizes:

• 2-Gang roll-bar mounted panel
• 3-Gang roll-bar mounted panel
• 4-Gang roll-bar mounted panel
• 6-Gang roll-bar mounted panel
• 8-Gang roll-bar mounted panel

Assembly Instruction:

This roll-bar-mounted switch panel holds 3 standard sized rocker switches.

• Convenient location
  Place your switches overhead on the bar. This unit is “ambidextrous:” you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Attractive and Durable
  This switch panel box is 3 3/4″ wide (3.75″). The walls are 1/8″ thick. This switch panel won’t warp in the heat – the material used has similar characteristics as the factory plastic in your machine. This product is 3D printed.
• Customizable
  If you need a switch panel for another bar size, or other combination of switches and circle-holes, contact me.

I don’t sell electronics, but you can get switches and things on Amazon: SXS Rocker Switches

Check out the other sizes:

• 2-Gang roll-bar mounted panel
• 3-Gang roll-bar mounted panel
• 4-Gang roll-bar mounted panel
• 6-Gang roll-bar mounted panel
• 8-Gang roll-bar mounted panel

Assembly Instruction:

This Pioneer 700 electronics switch panel mounts onto the Pioneer 700 dash underneath the shifters. It holds standard sized rocker switches, and includes a circular hole for USB/voltage meter mounting.

• Convenient location
  This switch panel mounts onto the lower dash of your Pioneer 700, below the shift levers. Panel is angled to point the switches upward..
• Easy install
  Mark and drill four holes. Fastens to the dash with screws (included). Some dash cutting necessary.

Panel is professionally 3D printed for a factory appearance.

This Pioneer 700 electronics switch panel mounts into the upper cubby and holds standard sized rocker switches, and includes circular knockouts for USB/voltage meter mounting. This panel comes with the slots “closed” with removable “knockouts.”

• Convenient location
  This switch panel mounts into the upper cubby on your Pioneer 700.
• Easy install
  Mark and drill four holes. Fastens to the dash with push-clips (included).

Panel is professionally 3D printed for a factory appearance.

This 1″ standoff creates more space for rocker switches to be installed in the area behind the dash warning plate.

There is a bar that goes across underneath the warning plate which blocks switch installation low in the space, and this standoff allows switch panels intended for the Pioneer 1000 to be installed on the P700.

This standoff is not necessary for Crossroads 3D P700 panels, and is not compatible with panels that use push clips as fasteners.

The six fastener holes are 4mm in diameter. Fasteners not included.

Panel is professionally 3D printed for a factory appearance.

This roll-bar-mounted switch panel holds 8 standard sized rocker switches, or 6 switches and two circular electronics. Choose your bar size and which face layout you want (A,B,C,D). The panel is 10.5″ wide.

• Convenient location
  Place your switches overhead on the bar. This unit is “ambidextrous” – you can mount your switches over or under the bar, forward, or rearward (toward or away from your face.)
• No cutting or drilling
  No chopping up of your dash!
• Easy install
  Installation is simple and uses a Phillips screwdriver.
• Attractive and Durable
  This 8-gang switch box is 10 1/2″ (10.5 inches) wide. The walls are 1/8″ thick. This switch panel won’t warp in the heat – the material used is the same as the factory plastic in your machine. This product is professionally 3D printed.
• Customizable
  If you need a switch panel for another bar size, or other combination of switches and circle-holes, contact me.

Check out the other sizes:

• 2-Gang roll-bar mounted panel
• 3-Gang roll-bar mounted panel
• 4-Gang roll-bar mounted panel
• 6-Gang roll-bar mounted panel
• 8-Gang roll-bar mounted panel
• 8-Gang flat-mounted panel